Avocent SC8 Manual do Utilizador descarregar pdf

CONSOLE

HGFEDCBA

Switching your servers

Press the appropriate front panel button labeled A-H to

access servers in your SwitchView switching system.

LEDs

Each target port (A-H) has dual LEDs on the front panel. A

green LED indicates the target device is on and connected

to the switch. An amber LED indicates the target device

is selected (KVM session).

Environmental

Operating Temperature: 41˚ (5˚C) to 104˚ (40˚C)

Storage Temperature: -4˚ (-20˚C) to 122˚ (50˚C)

The Power of Being There

Quick Installation Guide

Cybex

SwitchView

SC8 DVI Switch

The following instructions will help you

install your SwitchView SC8 DVI switch.

Should you require further assistance, please

contact Avocent Technical Support.

To install the Cybex SwitchView SC8 DVI switch

To Contact Avocent Technical Support: Visit www.avocent.com/support

Avocent, the Avocent logo, The Power of Being There, Cybex and SwitchView are registered trademarks of Avocent Corporation or its afﬁliates. ©2007 Avocent Corporation. All rights reserved. 590-502-501D

Connecting local peripherals

Power down all servers that will be part of your

SwitchView SC8 DVI switching system. Locate

your PS/2 keyboard, DVI monitors and PS/2

mouse.

Plug your DVI monitor cables into the

CONSOLE ports on the left side of the back

of your switch

. Plug your PS/2 keyboard cable

and your PS/2 mouse cable into the keyboard

and mouse ports respectively.

Connecting your servers

Locate your ﬁrst cable set consisting of two

PS/2 cables and one or two DVI cables. The

SwitchView SC8 DVI switching system has

eight port sets labeled A-H on the rear of the

unit. Plug the two PS/2 cables (keyboard

and mouse) and the DVI cable (monitors)

into the corresponding ports on your server.

Plug the other ends into any available server port

set on your SwitchView SC8 DVI switching system.

Repeat this process until all servers are properly

attached to the SwitchView SC8 DVI switch.

Turning on your system

L o c a t e t h e p o w e r c o r d t h a t c a m e w i t h y o u r s w i t c h .

Plug one end into the IEC power connector on

the SwitchView switch. Ensure the power switch

is off, then plug the other end of the power cord

into an AC wall outlet. Turn on your switch ﬁrst,

then turn on all attached servers.

Input Power: 60 W; Operating Voltage 100-240 VAC

Power Frequency: 50-60 Hz

Supported Hardware

Server: IBM, PC/AT, PS/2 and 100% compatibles

Video Modes: VGA, SVGA, XGA, SXGA, UXGA,

HDTV and QXGA

Maximum Resolution: 2048 x 1536 @ 75Hz

Peripherals: PS/2 keyboard, PS/2 mouse and

IntelliMouse (PS/2 only)

Mechanical

H x W x D = 3.6” x 17.2” x 10.8” (9.1 x 43.7 x 27.4 cm)

Weight = 9.5 lbs (4.3 kg)

Optional

RF ground

(not required

for safety)

1 2

Resumo do Conteúdo

Página 1 - SwitchView

CONSOLEHGFEDCBASwitching your servers Press the appropriate front panel button labeled A-H to access servers in your SwitchView switching system.LEDsE

Página 2 - INSTRUCTIONS

USA NotiﬁcationWarning: Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user’s auth

Comentários a estes Manuais

Sem comentários

Avocent SC8 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Interruptores KVM Avocent SC8. Avocent SC8 User's Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Interruptores KVM Avocent SC8