Avocent Network Adapter EMS1000P Guia do Utilizador Página 73
- Página / 80
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Command Description
ATE1 Enables the command echo (default).
ATH0 Hang up.
ATH1 Forces the modem off-hook.
ATI0 Reports product code.
ATI2 Reports OK (for software compatibility).
ATI3 Reports the firmware version of the modem. Example: CX810801-V90.
ATL0 Sets the speaker volume off.
ATL1 Sets the speaker volume low (default).
ATL2 Sets the speaker volume medium.
ATL3 Sets the speaker volume high.
ATM0 Speaker is always off.
ATM1 Speaker is on during call establishment but goes off when carrier is detected (default).
ATM2 Speaker is always on.
ATM3 Speaker if off during dialing and when receiving carrier but on during answering.
ATQ0 Enables result codes to the DTE (default).
ATQ1 Disables result codes to the DTE.
ATSr Establishes S-register “r” as the default register.
ATSr=n Sets S-register “r” to the value “n.”
ATSr? Reports the value of S-register “r.”
ATV0 Enables short-form result codes.
ATV1 Enables long-form result codes.
ATW0
Upon connection, the modem reports only the DTE speed (for example, CONNECT 9600). Subsequent
responses are disabled (default).
ATW1
Upon connection, the modem reports the modulation type, line speed, the error correction protocol and the
DTE speed. Subsequent responses are disabled.
ATW2
Upon connection, the modem reports DCE speed (for example, CONNECT 2400). Subsequent responses
are disabled.
ATX0 Ignores dial and busy tone. Sends CONNECT message when a connection is established by blind dialing.
ATX1
Disables monitoring of busy tones. Sends only OK, CONNECT, RING, NO CARRIER and ERROR
messages. If busy tone detection is enforced and busy tone is detected, NO CARRIER will be reported instead
of BUSY. If dial tone detection is enforced or selected and dial tone is not detected, NO CARRIER will be
reported instead of NO DIALTONE.
ATX2
Disables monitoring of busy tones. Sends only OK, CONNECT, RING, NO CARRIER, ERROR, NO
DIALTONE and CONNECT XXXX. If busy tone detection is enforced and busy tone is detected, NO
CARRIER, will be reported instead of BUSY. If dial tone detection is enforced or selected and dial tone is not
detected, NO CARRIER will be reported instead of NO DIALTONE.
ATX3
Enables monitoring of busy tones. Sends only OK, CONNECT, RING, NO CARRIER, ERROR, NO
DIALTONE and CONNECT or CARRIER XXXX. If dial tone detection is enforced and dial tone is not
detected, NO CARRIER will be reported.
ATX4 Enables monitoring of busy tones. Sends all messages (default).
ATZ0 Soft reset.
AT&C0 DCD remains on at all times.
AT&C1 DCD follows the state of the carrier (default).
AT&D0 Ignores DTR.
AT&D1 Enters the escape mode when ON-to-OFF transition is detected on DTR.
AT&D2
Hangs up, assumes command state and disables auto answer upon detecting ON-to-OFF transition of DTR
(default).
Appendices 65
- INSTALLER/USER GUIDE 1
- European Union Notification 2
- USA Notification 2
- Canadian Notification 2
- Japanese Notification 2
- Korean Notification 2
- Installer/User Guide 3
- Symbols Used 4
- Introduction 1 5
- Installation 7 5
- Appendices 59 7
- Introduction 9
- Web manager 10
- IPv4 and IPv6 support 10
- Flexible users and groups 10
- Security 10
- Authentication 11
- Packet filtering 11
- Configuration Example 12
- Chapter 1: Introduction 5 13
- Installation 15
- Connecting the Hardware 16
- Turning On the Console Server 19
- Configuring a Console Server 20
- Wizard Mode 24
- Expert Mode 26
- System Tools 26
- DSView 3 software security 27
- FIPS module 27
- HTTPS Certificate 28
- Bootp Configuration Retrieval 29
- Date and Time 30
- Help and Language 30
- Boot Configuration 31
- Information 32
- Settings 32
- IPv4 and IPv6 static routes 33
- Firewall 34
- IPSec(VPN) 36
- SNMP Configuration 37
- Serial ports 38
- Table 3.6: Dial-in Parameters 41
- Table 3.7: Power Parameters 42
- Auxiliary ports 43
- CAS Profile 43
- Auto discovery 44
- Pool of CAS ports 45
- Dial-in Profile 46
- Dial-out Profile 47
- Pluggable Devices 49
- Appliance authentication 50
- Authentication servers 50
- Local accounts 52
- User groups 53
- Managing user groups 55
- Table 3.11: ts_menu Options 56
- DSView software access rights 58
- Event Notifications 59
- Trap Forward 60
- Data Buffering 60
- Appliance logging 60
- Power Management 61
- Outlet Groups 63
- Active Sessions 64
- Monitoring 65
- Change Password 65
- Serial Viewer 66
- App e nd ic e s 67
- DSView 3 Software 69
- Appendix E: Internal Modem 72
- Appendices 65 73
- AT+MS modulation selection 74
- AT S registers 75
- Basic modem result codes 76
- Digital line guard 76
- Sleep mode operation 76
- Disconnecting a call 77
- Selecting country codes 77
- Using caller ID 78
- Appendix F: Technical Support 79
- For Technical Support: 80
Manuais e produtos relacionados com Servidores para consolas Avocent Network Adapter EMS1000P
(96 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais